Gongyi Qianjiaxin Refractory Material Co.LTD
5 1

Black/Green Silicon Carbide for Abrasive & Refractory

Contact Now* Send an Inquiry to this supplier.
or
Start Order * Name your price

Contact us

Gongyi Qianjiaxin Refractory Material Co.LTD
[China]

Address
185 Longhai Road , Zhengzhou Zhengzhou Henan
Phone
86-150-38364699
Contact name
Eva lu

Quick Information

  • Brand Name: Qianjiaxin
  • Place of Origin: China
  • Model Number : MM004
  • Abrasive Grain Sizes : According to customer requirements
  • Material : Quartz sand , coal tar , petroleum coke
  • Usage : Abrasive & Refractory
  • Sample : Free
  • SIC : 98.5%
  • Fe2o3 : <0.6%
  • hardness : 9.6

Description

Black/Green Silicon Carbide for Abrasive & Refractory

 

Introduction of the silicon carbide:
Silicon carbide is made of quartz sand, stone tar (or coal), wood chips and other raw materials in the resistance by high temperature smelting, silicon and carbon bonds made of ceramic compounds. Silicon carbide exists in nature in the form of rare minerals such as mozanite. Since 1893, silicon carbide powder has been used extensively as abrasive. The sintered silicon carbide powder can provide hard ceramic-like silicon carbide particles and can be used in materials such as automotive brake pads, clutches and ballistic vests that require high durability, such as light-emitting diodes, early radio detectors Classes are also used in the manufacture of electronic devices. Silicon carbide is now widely used in the manufacture of high temperature, high voltage semiconductors. By lely method to grow large pieces of silicon carbide single crystal. The gemstone of artificial mulberry is obtained by cutting the bulk silicon carbide single crystal prepared by the Lely method.
At present, China's industrial production of silicon carbide is divided into black silicon carbide and green silicon carbide two, are hexagonal crystal, green silicon carbide and black silicon carbide is basically the same, but the raw materials and manufacturing processes are produced, the product was green translucent body , Hardness, purity are better than black silicon carbide.

editorimg

editorimg

Commonly size: 
Section of sand: 0-1, 1-3, 3-5, 5-8mm
Granular: 16, 20, 24, 30, 36, 46, 60, 80, 100, 120, 150, 180, 200, 220, 320mesh
Powder: 325, 400, 600, 800, 1000, 1200, 1500, 1800, 2000, 2500, 3000mesh

 

Features of the silicon carbide:

  1. High hardness.
  2. Good thermal conductivity.
  3. Small thermal expansion coefficient.
  4. Chemical stability.
  5. Good wear resistance.

Usage of the silicon carbide:
Firstly: Silicon carbide is mainly used as abrasive in manufacturing grinding wheel, abrasive paper, abrasive belt, abrasive, grinding, grinding head, grinding paste, etc.
Sic grinding tool can be used in the manufacture of consolidation, coated abrasive grinding and freedom, to the processing of glass, ceramic, stone, jade, cast iron, stainless steel, floor tile and some non-ferrous metals, hard alloy, titanium alloy, high speed steel props and grinding wheel etc.
 
The second: refractory materials (silicon carbide powder, silicon carbide particles)
Silicon carbide as inorganic nonmetallic materials with high temperature resistant, wear resistant characteristics of silicon nitride combined with silicon carbide products can be used in the blast furnace ceramic cup, etc.In air brick as ladle with magnesia carbon brick, aluminum silicon carbide can also act as antioxidants added.

Made of silicon carbide refractory plate high crushing strength, long service life, low thermal capacity, low thermal conductivity.The brittle material, good toughness;Good flatness, size accurate,Easily cut installation, construction is convenient;Excellent resistance to wind erosion performance;Continuous production, uniform fiber distribution, stable performance;Excellent sound-absorbing noise reduction performance.
 
Third: steel making, casting industry (particles of silicon carbide, silicon carbide, silicon carbide, silicon carbide powder)
Silicon carbide as steelmaking deoxidizer can make molten steel quality is stable, and has fine grains, remove steel always harmful impurities, after using molten steel casting temperature, casting are of good quality and low cost per unit.
Silicon carbide can be all alternative ferrosilicon and recarburizer FeALSi dosage decreased, which can effectively reduce the cost of steelmaking.
Decomposition of silicon carbide at high temperature and oxidation is exothermic reaction process, positive pressure in the furnace is strong, and can guarantee lower sulfur content.
 
Fourth: photovoltaic industry, polishing, grinding, high-tech research and development, and other industries (silicon carbide micro powder)
Silicon carbide powder is mainly used for refractory products manufacturing, and foam ceramic industry, solar silicon original cutting, crystal cutting, grinding, car engine manufacturing, special coating industry, plastics modification, desulfurization, power supply, environmental protection industry, etc.

 

 


Price

  • Delivery Port : Tianjin

Packaging & Delivery

  • Packing :25kg a Bag
  • Packaging Size : 80 x 50 x 10   Centimeters
  • Package Weight : 25  Kilograms
  • Delivery Lead Time : 7-10 Day

Product Image

  • Black/Green Silicon Carbide for Abrasive & Refractory image

Related products from premium suppliers on EC21

Send an Inquiry to this supplier

Send an Inquiry to this supplier
* From
  To Eva lu
Gongyi Qianjiaxin Refractory Material Co.LTD
* Buying Product
- Please enter your specific buying item.
e.g. 42 inch LCD TV, leather executive chair
Category : Abrasives
* Message

Use English only Max. 2000 characters. (Min. 20)

Send
EC21.com does not guarantee the validity of product information or the credentials of sellers.